Adjust Settings for Auto Backlight on a FieldLab during a Data Logging Test

Use FieldLab Desktop to control the amount of time that the backlight stays on before shutting off automatically to conserve battery life.

Each Test Mode has its own settings. When you Activate a Test Mode on the FieldLab, whatever the settings are for in that Test Mode will apply to the FieldLab as long as that Test Mode is active.

Adjust the Auto Backlight Off Settings for Test Modes

1

Open FieldLab Desktop on your computer.

2

Select Test Modes from the main navigation.

3

Select the Test Mode that you wish to change the Auto Backlight Off settings for.

4

Adjust the Auto Backlight Off settings to your liking and Save Changes.

5

Save Changes

You will need to Sync for the changes to take effect.

• Related Articles

• Run a Hydrostatic Test on a FieldLab

  Use a FieldLab and one or more Field Gauges/Process Meters to perform a Hydrostatic Test. Overview This article will show you how to use a FieldLab and one or two Field Gauge LC20s/Process Meter LC30s to perform a Hydrostatic Test with one pressure ...

• Run a Pressure Safety Valve/Pressure Relief Valve Test on a FieldLab Pressure Calibrator with auto-crack detection

  Use a FieldLab to automatically detect & record the exact pressure at which a valve cracks and reseats, with the additional option of recording Seat Tightness Test results. This features requires FieldLab Desktop version 1.24.0 or later. Download the ...

• Run a Snapshot Logging Test on a FieldLab

  Log multiple single-pressure points and save them to one data set on an intrinsically safe Ralston FieldLab Pressure Calibrator. What you will need: A Ralston FieldLab Digital Pressure Calibrator with:  A max pressure that will accommodate your ...

• Run a Calibration Test on a FieldLab Pressure Calibrator

  Use a FieldLab to test the accuracy of another device.  Step-by-step instructions 1. Create a Calibration Test and Add it to the FieldLab. 2. Add your new Calibration Test to the FieldLab. 3. Make the proper connections. Make airtight connections ...

• Quick-Start Guide and User Manual for the FieldLab Pressure Calibrator

  Download in PDF format below.

• Recent Articles

• Turn Bluetooth radio on or off on a Field Gauge LC20 or Process Meter LC30

  This article applies to all Field Gauge LC20 and Process Meter LC30 models equipped with a Bluetooth radio. To determine if your gauge is Bluetooth enabled: Check the last two characters in the model number printed on the gauge. If they are "B1", the ...

• Operation Instructions 10,000 psi Hand Pump (Model XTHP)

  Add Fluid 1. Remove the vent plug 2. Add fluid to the Fluid Chamber Acceptable fluids: Ralston Calibration Oil, mineral oil, transmission fluid, water, or alcohol. Add around 2 inches of fluid, or enough fluid to keep the bottom of the fluid ...

• Operation Instructions 5000 psi Hand Pump (Model QTHP)

  Add Fluid 1. Remove the Vent Plug at the top of the Fluid Chamber 2. Add fluid to the Fluid Chamber Acceptable fluids: Ralston Calibration Oil, mineral oil, transmission fluid, water, or alcohol. Remove the vent plug and add around 2 inches of fluid, ...

• Connect one or more Ralston gauges to FieldLab Desktop App with Bluetooth

  What you will need: One or more Bluetooth-enabled Ralston Gauge. How to tell if your Field Gauge has Bluetooth. The FieldLab Desktop app installed on your Windows computer. Version 1.40.4 or later. Update FieldLab Desktop to the Latest Version. 1. ...

• A Gauge is Overpressurized

  Before applying pressure to your Ralston gauge, confirm that the gauge is rated for higher than the max pressure that will be applied. Gauges that have been overpressured above 33% of max rating will be unable to display or log accurate pressure ...