Adjust Logging Interval in Manual Mode for a FieldLab Digital Pressure Calibrator

Use FieldLab Desktop to adjust the length of time between each point logged on a FieldLab while in Manual Mode.

1

Open FieldLab Desktop on your computer.

2

Plug the FieldLab into your computer with the provided USB Cord and Power it On.

3

On the FieldLabs screen, select the FieldLab you'd like to adjust the settings for.

4

Select the Settings Tab

5

In the Manual Mode section, select the Change Button.

6

Adjust the Logging Interval settings.

7

Save your changes by selecting the Save Changes button.

• Related Articles

• Change Display Sleep Timer on a FieldLab for a Data Logging Test

  When you Activate a Test Mode on a FieldLab Digital Pressure Calibrator, the settings for that Test Mode will apply to the FieldLab as long as that Test Mode is active. Each Test Mode has its own Auto Display Sleep settings. You can use FieldLab ...

• Adjust settings for Auto Power Off for a FieldLab Pressure Calibrator while in Manual Mode

  Use FieldLab Desktop to adjust the length of time before the FieldLab automatically Powers Off off to conserve battery life. Each Test Mode, including Manual Mode, has its own Auto Power Off settings. When you Activate a Test Mode on the FieldLab, ...

• Create a Snapshot Logging test

  Create a Snapshot Logging Test in FieldLab Desktop that you can sync & run on a Ralston FieldLab, or use a FieldLab or Field Gauge connected to your PC and log the data directly to FieldLab Desktop. Things you will need to create the test. A PC ...

• Log pressure and/or temperature data to your computer with FieldLab Desktop

  This article applies to the following products: Field Gauge LC10, all models Field Gauge LC20, all models Process Meter LC30, all models FieldLab Digital Pressure Calibrator, all models. Things you will need: A PC running Windows.  FieldLab Desktop ...

• Calibrate the pressure sensor on a Field Gauge, Process Meter, and FieldLab with FieldLab Desktop.

  At the end of this process, FieldLab Desktop will compare the readings from your Reference device and Ralston Gauge (Zero, Mid Point, and Full Span). If it is out of spec; FieldLab Desktop will automatically make any necessary adjustments to bring ...

• Recent Articles

• Turn Bluetooth radio on or off on a Field Gauge LC20 or Process Meter LC30

  This article applies to all Field Gauge LC20 and Process Meter LC30 models equipped with a Bluetooth radio. To determine if your gauge is Bluetooth enabled: Check the last two characters in the model number printed on the gauge. If they are "B1", the ...

• Operation Instructions 10,000 psi Hand Pump (Model XTHP)

  Add Fluid 1. Remove the vent plug 2. Add fluid to the Fluid Chamber Acceptable fluids: Ralston Calibration Oil, mineral oil, transmission fluid, water, or alcohol. Add around 2 inches of fluid, or enough fluid to keep the bottom of the fluid ...

• Operation Instructions 5000 psi Hand Pump (Model QTHP)

  Add Fluid 1. Remove the Vent Plug at the top of the Fluid Chamber 2. Add fluid to the Fluid Chamber Acceptable fluids: Ralston Calibration Oil, mineral oil, transmission fluid, water, or alcohol. Remove the vent plug and add around 2 inches of fluid, ...

• Connect one or more Ralston gauges to FieldLab Desktop App with Bluetooth

  What you will need: One or more Bluetooth-enabled Ralston Gauge. How to tell if your Field Gauge has Bluetooth. The FieldLab Desktop app installed on your Windows computer. Version 1.40.4 or later. Update FieldLab Desktop to the Latest Version. 1. ...

• A Gauge is Overpressurized

  Before applying pressure to your Ralston gauge, confirm that the gauge is rated for higher than the max pressure that will be applied. Gauges that have been overpressured above 33% of max rating will be unable to display or log accurate pressure ...